After 10 Years the Step Works

For 10 years, the automatic step by the motorhome door would not work without pulling the dirty step out by hand. I sprayed INOX MX-4 on the step parts and the next day when I opened the door, the step popped out all by itself, just like brand new. The MX-4 cut through all the grime, rust, salt, and dirt build up because the MX-4 is waterproof it will just keep on working great Next I did the hinges, springs, cables, pins and latches on my race car trailer and the next day when I opened the ramp, it came down so easy that it surprised me. I don't think it ever worked that good! MX-4 is the best lube I have ever used.

Steve L.
Baltimore, OH

Grandma's Old Rocker

Grandma's old rocker always squeaked. Whenever we had a family reunion, someone would comment that the chair sure made a lot of noise. I happened to have a can of INOX MX-12 Supa Lube in my car and got it to spray on the wood parts that rubbed. You are suppose to wait 24 hours but we waited only 5 minutes and the squeak stopped. My contractor brother-in-law said, "I never knew you could lubricate wood." We were all amazed!

Dan K.
Addison, IL

Restored My Electric Drill

The old Milwaukee electric had a hand chuck on it that froze up. To get a bit in or out of the drill, I'd have to use vice grips and channel locks. The last time it stuck, I even burred it trying to break it loose. I sprayed INOX MX-3 on it, waited a day and the chuck spins free in my hand as soon as I pulled the trigger. This stuff is amazing. I saved myself $150 since I can keep using my old drill.

Scott M
Athens, TN

Made My Wrench Good As New

I had this old cresent wrench in my tool box that just wouldn't work. I even soaked it in oil for a week. Since it as a Sears wrench I could have taken it back but I never did. I sprayed INOX MX-3 on it and the next day the wrench worked better than new. I was so impressed with how good the MX-3 was that I went around the house and sprayed all the door locks, hinges, and windows that were hard to open. MX-3 fixed everyone of the problems I had. I'd recommed INOX to everybody. All the other lubes I've used don't even compare.

Paul B.
Spring Hill, FL

Revitalized Old Guns

My grandfather gave me his BB gun when I was a kid and it is now over 70 years old. It rusted up over all these years and wouldn't work anymore. I sprayed INOX MX-3 on it and the next day, the rust was gone and it works fine. Then I tried it on my valuable pistol made in 1911 and the MX-3 cleaned it all up and took a hundred years of old grime and powder residue completely off. MX-3 is amazing!

Fred K.
Jefferson City, TN

Dehuminifier Bearings and Fan Motor

"My Father and I were working on a dehumidifier that hasn't worked well for 15 years. It was extremely loud, made a lot of vibration noises, etc... When we finally got the unit apart, the coil's circulation fan, motor, & shaft were so corroded and tight it couldn't be turned. Now my father is not a "gimmicky" kind of guy and still had reservations about using INOX, suggested using copious amounts of "WD" products instead, but admitted he didn't know what much good that would do since it'd just dry-up. Well, we tried spraying some INOX MX-5 on all points of contact, the shaft, and the corroded portions of very the small bushing bearings. Within 60-seconds (yes, I really timed it), the housing freely spun as did the fan & shaft. Keep in mind this is in 38 degree Chicago weather!" We've got a believer/convert out of one use, of just one of the INOX products. Now he is using our INOX on the compressor for this unit as well as, all the rings, seals, and hoses. Restoring a 32 year old machine into a smoother cooler running, quiet, efficient unit saving them the purchase price of getting a new one."

Joe K.
Addison IL

Ceiling Fan Repair

We had some ceiling fan motors that were a little louder than normal. I grabbed some INOX MX-3 and went to spray it into the motor vents on the bearings. I thought my brother (a contractor & home insurance adjuster) was going to have a heart-attack thinking the fan was about to burst into flames! I calmly sprayed it in. Out came a bunch of grime and dust and the fan is running like it came out of the box. I explained that MX 3 is non-conductive and anti-static. He's now going to recommend all his insurance clients and homeowners doing re-modeling projects that they keep a can of INOX MX-3 in every kitchen and garage.

Dan K.
Addison, IL

Testimony - INOX MX-4 LANOX

Testimony INOX MX-4

Testimonies - INOX MX-2

Below are emails received from Mr. Winn. They are self explanatory on INOX MX-2 Battery Conditioner.

-----

Following your advise after 60 ml of conditioner was added, there was a significant decrease in sludge in the bottom of the batteries over a 4 month period.

The batteries also are working better. I have now treated all the batteries I have after the first two trial ones. Thank you for your kind advice. I shall certainly recommend MX-2 Battery Conditioner to all concerned.

Thanks again,

Mr. Winn

-----

RE: My solar batteries - one set 9 years old, the other 10 years

It is now 13 months since I first contacted you in regard to my solar batteries, forming sediment on the bottom and getting close to shorting out the batteries. You recommended your INOX MX-2 Battery Conditioner and suggested the dosage.

Thanks to your MX-2 Battery Conditioner, the batteries are still going strong, and the sediment is gradually getting less and less.

Thank you for your help. I would recommend MX-2 Battery Conditioner to all that would listen.

Respectfully,

Mr. Winn

Burring on Welder’s Metal Cut

Problem: After welding metal, burrs must be removed taking additional time.

Application: Apply INOX MX-3 on the cut line and the deburring grinding time will be drastically reduced.

Solution: The MX-3 does not hinder the cutting and almost eliminates the burring on the metal that has been cut.

Batteries on Trolling Boats

Problem: The batteries on our fishing boat’s trolling motors are generally recharged when the boat is at the dock, since many of the boats do not have generators on board. Our operation time during use was going down at a rate of 2% a month so trolling times got shorter and shorter while the recharge time kept going up. The old solution was to replace batteries which added cost and drove profits down.

Application: We treated the boat batteries a with a simple process by adding the INOX MX-2 Battery Conditioner to the batteries just as you would add water to a low cell, and it revitalized the batteries.

Solution: Trolling times increased from 1 hour to 3 or 4 hours…sometimes up to 6 hours.

We found that the batteries were lasting much longer, making the fishermen happy, and recharging was much faster cutting our electric expense. The MX-2 reversed the batteries decline, and returned them close to new specs. We now add MX-2 to every new battery to extend its life to 2 or 3 times the manufacturer’s warranty.

Underwater Boat Damage

Problem: The hull and underwater running gear on boats operated in salt water face a double whammy, the corrosion of the environment and the growth of sea life on any exposed surface. The cost of the corrosion is obvious and the sea growth causes drag that decreases fuel efficiency and performance.

Application: INOX MX-4 Lanolin Grease provided the solution to our problem. Coating all underwater surfaces with it provides a non-toxic answer to both the corrosion and growth.

Solution: The metal surfaces of running gear and trailer hardware are protected from corrosion and when applied to the hull, sea growth is prevented because MX-4 Lanolin Grease is a food grade product, it is not harmful to the environment or to the person applying it.

Metal Bending

Problem: Metal bending and distortion of the shape of the bent pipe.

Application: INOX MX-3 applied on the bender to ease the flow and reshaping of the pipe.

Solution: With MX-3 on the metal bender the tubing does not bind up and reduces the stress in the bender.

Kart Racing

Problem: Kart racers, like all racers face mechanical failures caused by dirt, corrosion and wear. All mechanical failures mean you don’t win, and poor lubrication costs speed…another no win.

Application: We spray and wipe down INOX MX-3 lubricant on all parts of the kart; we wipe MX-3 on the kart body to reduce after race clean up, lubricate the throttle linkage and cables because the MX-3 eliminates sticking, and coat aluminum engine parts to protect them from white rust, corrosion and pitting. MX-3 penetrates into the metal and reduces friction which means we are saving money because we don’t have to replace parts as often. Gears and chains now last a season not just a month.

Solution: INOX MX-3 is a superior surface lube compared to all the others we’ve used because it does not dry out, doesn’t become tacky and gummy in dirty and dusty track conditions, and MX-3 protects all the surfaces of the kart… we now wouldn’t race without it. $10 is far cheaper for us than a $500 to $1,000 engine rebuild. Best of all we win using INOX MX-3.

Protecting Electronics on Fishing Boats

Problem: The electronics and wiring on all fishing boats are subject to one of the most extreme and harsh environments known to man. Boaters invest huge sums to stop water and salt damage and corroded connections that can literally dissolve circuit boards. Short circuits can cause engine failures, radio and navigational outages, and very expensive repairs and replacements.

Application: We apply a light coat of INOX MX-4 LANOX to the wiring, electronics, connectors and even the digital display screens. LANOX MX-4 is non-conductive, doesn’t dry out, provides a lubricant surface that causes moisture to simply run off and because it is lanolin based instead of solvent based, it does not adversely affect the components. Best of all it is water and salt proof.

Solution: Since using INOX MX-4 LANOX our electronic and electrical problems have all but disappeared. We now enjoy the business of operating our boats and spend less far time fixing problems.

Fishing Reel Drag

Problem: Our fishing reel drags were surging, sticking or not operating at all and if they got wet they would hydroplane like an automobile on wet pavement.

Application: INOX MX-6 Food Grade Machinery Grease
We applied the MX-6 to the cork surface on the reel drag, as well as on all the interior reel gearing to protect them from corrosion, rust, and binding.

Solution: INOX MX-6 provides a waterproof lubricating surface that doesn’t spin off, doesn’t dry out and provides for an even, consistent drag pressure, protecting the reel drag surface from drying out and absorbing water, it also completely stopped the hydroplaning.

MIG Welding

Problem:  Welders have the MIG wire jam or bind in the tip when welding causing a blow out and a ruined tip.

Application: Apply INOX MX-3 to a small felt pad on the wire feed which will stop the wire from jamming.


Solution: With the INOX MX-3 the welder can keep welding without stoppage saving money on ruined tips.